Recommended sizes
5'9"-6'8"
Tail Options
The S2 features a subtle bump wing 15" from the tail. It features a semi-full tail with a narrower tail block than the S-10.
-
Squash Tail
Standard on the S2, has a slightly narrower tail block than the S-10
-
Round Pin Tail
Put into the S2 template, the effective rail line used in a turn becomes shortened. With respect to board length, there will be less area on the tail to penetrate the wave face and you can actually sink a section of tail deeper than other templates.
Types of Tails
Round Pin Tail
- Moves the "sweet spot" slightly farther ahead on the board, in front of the fin cluster.
- Offers a different release & hold for deep carves and more drawn out turns
- Shortens the "effective rail line" and with respect to board length, resulting in less area on the tail to penetrate the wave face so that you can actually sink a section of tail deeper than other templates.
Thumb Tail
- Softens the pivot points on the end of the rail line while keeping a smooth flow like a round pin without taking away the tail width
Squash Tail
- Top to bottom surfing
- Free the tail on all your turns
- HIt the lip and more while you rip it down the line.
Bat Tail
- Offers a more pivotal, snappy feel
- Loosens up the board by having the rail line end shorter
- Relative to other tails, the bat is wider at the block, allowing the rear foot to move further back in to the fin cluster.
- Combines the swallow tail feel but with more stability
Diamond Tail
- Offers an aesthetic alternative to the bat tail while keeping the same performance features
Swallow Tail
- Quick, loose and responsive for snappy turns off the top
- For similar results with a more distinctive look, try our Moon tail
Baby Swallow Tail
- Quick, loose and responsive for snappy turns off the top
- Baby swallow tail is a reduced version primarily used on big wave boards
Deep Swallow Tail
- Quick, loose and responsive for snappy turns off the top
- For similar results with a more distinctive look, try our Moon tail
Moon Tail
- With performance features similar to the swallow tail, the Moon adds a much more distinctive look.
Winged Tail
- Pulls in the outline at the trailing edge of the fins as a way to break the water along the rail line.
- Adds a snappier and more pivotal turning characteristic as opposed to a full rail turn.
Fin Options
The S2 comes standard as a tri. We recommend this board with smaller yet fuller, high aspect ratio fins from 4 1/4"-4 1/2".
- Choose from Future or FCS
Also Available
Outline
The S2 has the wide point exact center. This is a balanced template with a semi-full nose and semi-full tail. The subtle bump wing at 15" from the tail brings in the outline to a slightly narrower tail block than the S-10.
Rocker
Continuous rocker broadens the "sweet spot", increases turning ability and adds a "predictable" feel under your feet.
Rails
Stretch’s standard 50/50 rail with a thickness between the Ratskate and S-10. Like all of the performance models, it is shaped with the same amount of curve throughout, from top to bottom. Independent from the bottom of the board, it is a section of a sphere that is designed to hold the wave face no matter where you lean the board. The hard edge behind the front fins give a crisp release.
Bottom
Slight vee in the nose to a 5/16" deep single concave between your feet. Slight vee out the tail.
Construction
All Boards 6’5” and under include:
- 2lb PCF Marko EPS foam
- 3/16” Para Band Bass Stringers
- Hexcel RWG Direct Size “E” Cloth
- JPS Direct Size Bias Weave “S” Cloth
- Resin Research Epoxy Resin
- Deck Channels
- * Medium to heavy construction available above 6’5”
EPS/EPOXY
Prices by length for epoxy tri-fin surfboards.
| Size of Board |
Retail Price by Length |
Construction |
| Up to 6' 5" |
$749 |
Light |
| 6' 6" - 6' 11" |
$794 |
Medium |
| 7' 0" - 7' 5" |
$839 |
Medium-Plus |
| 7' 6" - 7' 11" |
$884 |
Medium-Plus |
| 8' 0" - 8' 5" |
$929 |
Heavy |
| 8' 6" - 8' 11" |
$974 |
Heavy |
| 9' 0" - 9' 5" |
$1019 |
Heavy |
| 9' 6" - 9' 11" |
$1064 |
Heavy |
| 10' 0" - 10' 5" |
$1109 |
Heavy |
| 10' 6" - 10' 11" |
$1154 |
Heavy |
Light Foam
- 1.9 - 2.1 PCF Density
- 3/16” Para Band Bass Stringer
- Single 6oz Direct Size Bottom
- Biased Weave 4oz Direct Size S cloth + 6oz Direct Size E-cloth Deck Lamination
Medium Foam
- 2.3 - 2.5 PCF Density
- 1/4” Para Band Bass Stringer
- Single Layer Bottoms, Single Layer Decks
Medium-Plus Foam
- 2.3 - 2.5 PCF Density
- 1/4” Para Band Bass Stringer
- Boards 7’0” - 7’11” Double Layer Bottoms, Double Layer Decks
Heavy Foam
- 2.8 - 3.0 PCF Density
- 3/8 Para Band Bass Stringer
- Boards 8’ 0” and above: Double Layer Bottoms, Triple Layer Decks
Extras
- Four Fin: + $10.00
- Parabolic Blank: + $65.00
- Weighting System: + $25.00 first 1lb. + $10.00 each additional lb.
- Additional cloth layers and patches: $6.00/yard
- Airbrush: Solid Color- +$20.00
- 2-Color Fades or Halos- + $35.00 (includes white)
- Pin lines: + $15.00 first pin + $10.00 each additional pin
Shipping
We use FedEx Ground to ship surfboards in the mainland USA.
The rates listed below are estimates we created for your convenience. To get an exact quote, use the RateFinder at the FedEx website.
FedEx Ground Shipping Rates Estimates by Box Size
| Box Size |
SoCal |
Pacific NW |
Texas |
Florida |
East Coast |
North East |
| Up to 108"x24"x4" |
$80-$85 |
$85-$90 |
$90-$95 |
$95 |
$100 |
$100 |
| 100"x23"x4" |
$75-$80 |
$70-$85 |
$85-$90 |
$85-$95 |
$85-$95 |
$90-$95 |
| Under 78"x22"x4" |
$35-$40 |
$35-$40 |
$45-$50 |
$50 |
$50 |
$50-$55 |
Shipping to Hawaii best rate to Oahu with Airline Cargo
